How to install fish finder transducer on boat

how to install fish finder transducer on boat
To pinpoint the right transducer for the given fish finder model, it's possible to input the associated serial number into the search box. You can fasten them with whatever kind of connectors you find more convenient. When dealing with larger craft, especially those designed for open water and that have an enclosed cabin, installing a transducer is usually more complicated.

If the device points away from the ground surface, test fitting should continue with settings B through E.

Upon finding the correct installation point, you can safely snug down the lock nut to complete this step. The transducer sends information to the display screen through specially designed cables. The insulated communication cables also contain a separate power wire that provides the transducer with juice from the boat's battery. The main set of cables run directly from the screen to the transducer.

Bayliner fishfinder Install

The screen utilizes a separate cable to pull power from the battery. The cables must run through the inner panels of the boat to prevent damage or moisture accumulation. To run the cables, simply pull up the bottom edge of the panels and push the cable into the cavity, leaving either end poking out for quick connection to the devices.

How To Install A Fishfinder

Use the cable ties to secure the cords at various junctions to prevent them from moving out of place. Finishing the cable install is as simple as plugging the ends into the right connection points. After connecting the system, it's important to install the 3-amp fuse in the battery line.

The fuse will protect the equipment if power surges unexpectedly. Upon turning on the system, you can check for system recognition of the transducer to confirm installation went as expected. It is more practical to first install the transducer then see how far the wires run — you can move your fish finder unit around, but your transducer has to go on the transom!

Look on the hull for a spot that always stays submerged in the water. The more turbulence there is, the more disturbance there will be in the reading.

how to install fish finder transducer on boat

If we did it after screwing it in, an accidental tug on the wire might cause the sealant we will apply to seal the holes to loosen. Instead, coil and clamp the wires or fasten them with ties near the main unit, NOT near the transducer. Place the transducer on the block in a position as discussed above, and mark the holes with a pencil.

This is where you will be drilling.

how to install fish finder transducer on boat

If you choose to fasten the transducer directly on the transom, mark the two holes, and drill through them. Screw the transducer in using the mounting hardware that came in the box, and apply a generous amount of silicone sealant on both holes both INSIDE and OUTSIDE — this will make sure that no water will leak through from anywhere — that could be quite a problem!

Otherwise, most fishfinders have a cord for the transducer of sufficient length for it to hang overboard and below the craft to get a good signal.

How to Install a Lowrance Transducer

These fishfinders usually require little more than a few bolts to be fixed to mounting points to install them and make good options for install that are rented, stored outside in all weather conditions, or boat situations where a fisherman may want to take his fishfinder home with him each day. Therefore, even on small craft, it is often necessary to conduct a permanent installation. Additionally, the position how the transducer is important both for getting an accurate finder and for ensuring it is not damaged fish the boat is placed in and removed from the water.

Fortunately, most modern fishing boats have dedicated mounting points, or even mounting holes, for transducers due to their popularity. This eliminates the need to drill holes in the transducer, or to attempt to secure the transducer with an adhesive. In the event, such an installation was not engineered for, be certain to talk to the manufacturer about the best way to install a transducer. Ideally, the hull should remain intact, with the transducer wire traveling over the exterior of the boat rather than through it, but there may be ways to route the wire through pre-determined holes.

While the basic principles of how they function are relatively simple, getting to know how to install, setup, operate, and master using one is a totally different story. It can be complicated using a fish finder, especially in your early stages of owning one.

One of the more difficult tasks to perform as a beginner fish finder owner is knowing how to properly setup and mount a fish finder. Two things on a fish finder need to be mount; the display and the transducer. The display is what shows the user the readings that transducer receives, meanwhile, the transducer is the part of a fish finder that is underwater and emits and receives sonar waves. Most fish finders displays are relatively to set up. This is standard for most fish finder displays, and is a rather quick procedure.

how to install fish finder transducer on boat

Next, you need to mark where your display will go, along with all the holes for where you plan on drilling. This should be pretty easy. Next you just need to attach the mount to the fish finder.

how to install fish finder transducer on boat

These types of fish finders are great for mobility, and can often be purchased for aftermarket modification. The problem with such a useful tool is that there are seemingly endless variations, each built to work best in slightly different scenarios. Some fish finders require holes to be drilled, while others need a specific type of material in order to be utilized.

Installing Your Fish Finder

Variety is good, but it can cause a little bit of confusion. The most common type of fish finder transducer type is the transom mount transducer. The majority of fish finders available for purchase now will come with a transom mount fish finder, simply because these are simple and relatively easier to produce. Transom mounts are made of plastic, or other easily mass produced materials, so they are increasing in popularity. Through hull transducers are more often utilized in sailing boats or large vessels.

how to install fish finder transducer on boat

Finally are the transducers that require the least amount of work and modification to your vessel — in hull transducers.


You will meet Exotic Russian Brides after Free Registration!

First Name
Email