How to perform a clean boot to troubleshoot a problem in windows vista windows 7
When you start the computer in clean boot, the computer starts by using a pre-selected minimal set of drivers and startup programs, and because the computer start with a minimal set of drivers, some programs may not work as you expected. All Microsoft services remain intact and ready to load when you reboot Windows. Most if not all of these services are required for Windows 7 to function properly.
By performing these two steps, you have effectively turned off all services from third-party software developers. All Microsoft services remain intact and ready to load when you reboot Windows.
Finally, click the OK button and reboot Windows 7. When you reboot, you may get messages that certain hardware and software are not unavailable.
In fact, by disabling these components in your PC, you can go back to the Services tab on the System Configuration window and turn on only those services known to be functioning properly. The rest you can turn on one at a time to troubleshoot the errors you were getting in Windows 7.
Once disabled, you can begin turning third-party services back on to diagnose your computer. Just be sure to hide all Microsoft services before you use the Disable All button. Otherwise, you may encounter boot up errors when you reboot your PC.Perform a Clean Boot in Windows 7 or Vista by Britec
March 1st, by Aseem Kishore File in: Windows 7 There are 0 comments, care to add yours? Although this procedure can be somewhat time consuming and you have to keep track of what your doing to avoid omissions or duplications, it's one of the best tutorials I've ever read on diagnosing a misbehaving machine. One caveat that you didn't seem to mention: If it's malware that's causing the problem, there's a possibility that it could prevent you from following these steps by any number of means, not the least of which is changing permissions so that even someone with administrative privileges cannot access the necessary data or utilize the normal Windows command set.
Perform a Clean Boot in Windows 7
I'd give it six stars, but I don't see a rating system, so this 'review' will have to do. Similar help and support threads Thread Forum Laptop not performing as it should be after clean reinstall I did a clean reinstall about a month ago but ever since my ASUS N55SF laptop has not been performing as it should do. Beforehand I could run the games I play with no problems but now I can barely load them. I have replaced my battery after thinking it was that laptop gets very hot and noisy Also restore the computer to the way it was before as instructed.
Now get an error msg when I start the computer. General Discussion Help with performing a clean install A few months back I discovered a rootkit on my laptop which was hiding in the winsxs folder.
I don't believe that it has been removed, but I can't detect it anymore. It doesn't cause any problems on the surface, but it is indeed causing some problems. So I plan on doing a clean install of Windows I've been experiencing problems with my laptop for probably a year now, it takes forever to start up when it's either shut down or in sleep mode.
After doing some research online and attempting some various fixes, I think my quickest solution is just to perform either a clean reinstall or a Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. All times are GMT You need to wait until you get to step 7 below.
Repeat this step until all startup programs are disabled. After the PC finishes restarting, determine if you still have the problem or not. If the problem still occurs after you restart the PC, then follow these steps: If the problem still occurs after another restart, uncheck half of the remaining checked boxes again until only one checked service is running when the problem occurs.
If the problem does not occur after you restart the PC, then follow these steps: If the problem still does not occur after another restart, check half of the cleared check boxes again.
Repeat this process until you have selected all the check boxes and the problem still does not occur.
Perform Clean Boot in Windows 10/8/7
If the problem occurs after another restart, uncheck half of the checked boxes that you last selected. Repeat this process again until you can isolate the one service that is running when this problem occurs.
If you can isolate one service that is checked when the problem occurs, that service is the one that is causing the problem. If you cannot isolate a service in this manner, a startup program might be causing the problem instead.
If you determine that a service is causing the problem, go to step 9 below. If you determine that a service is NOT causing the problem, go to step 6 below. Close Task Manager, and restart the PC. If the problem occurs after you restart the PC, then follow these steps: If the problem still occurs after another restart, disable half of the remaining enabled startup items again.